Description
ENFORCER Long-Range Barrier Sensors are ideal for protecting indoor or outdoor areas separated by long distances. They feature reliable photobeam technology with a choice of four programmable beam frequencies that provide superior perimeter protection by eliminating crosstalk and interference when multiple units are used. False alarms caused by animals, falling leaves, poor weather, or other sources are minimized by programming the alarm output trigger operation.
- Weatherproof (IP65) for indoor or outdoor perimeter security
- Long sensor range up to 190ft (60m) outdoors, 380ft (120m) indoors
- Install on windows, doorways, skylights, fence tops, and any place where space is limited
- End caps swivel so sensor can be mounted on a single wall or on opposite walls
- Programmable immediate trigger on simultaneous breaking of beams, or trigger after a single pair of beams is broken for at least 2 seconds
- Heater for use in cold weather operation
- Heater activates at 41ºF (5ºC)
- Terminal block wiring
- Slim design: 2-1/4″ x 1-7/8″ (55 x 49 mm)
- Rugged aluminum construction
- Built-in tamper switches, one on either end, trigger the alarm if end cap is removed
- No synchronizing wires required to align the beams
- Form C relay output
- LED and buzzer alignment indicators
- AGC (Auto Gain Control) circuits regulate beam signals in order to compensate for and ensure operation in rain, fog, and low-temperature conditions
- Programmable for 4 different frequencies to reduce interference between multiple units
Specifications
| Type | Long-Range Barrier Sensors for Indoor/Outdoor Access Control – Up to 380ft (120m) |
| Number of Beams | 4 pairs |
| Sensing Range | Outdoor- 190′ (60m), Indoor- 380′ (120m) |
| Buzzer Active Current | 20mA@12VDC (RX) |
| Heater Active Current | 160mA@12VDC (Rx+Tx) |
| Rx Standby Current | (Buzzer off) 80mA, heater off (+/-25%@12VDC) |
| Rx Trigger Current | (Buzzer on) 80mA, heater off (+/-25%@12VDC) |
| Tx Standby & Active Current | 84mA, heater off, (+/-25%@12VDC) |
| Input voltage | 12~24 VDC |
| Operating Voltage | 12~24VDC |
| Reaction time | 150/300/450/600 ms (DIP switch programmable) |
| LEDs – Red | Alignment LED (Rx only), ON – beam is broken / OFF – aligned |
| Detection System | Triggers as programmed when any 2 adjacent pair of beams are broken, or any single pair of beams is broken for over 2 sec. (programmable by JP2) |
| Alarm Output | NO/NC/COM, relay output, active for 1 sec. when triggered |
| Tamper Output | 1A@120VAC / 1A@24VDC (Tx & Rx) |
| Case material | Aluminum housing / PC anti-UV cover / ABS end caps |
| Operating Humidity | 0~95% |
| Operating Temperature | -49º~131º F (-45º~55º C) |
| Dimensions | 1-7/8″ x 2-1/4″ (49 x 55 mm) [Width x Height] |
| Alignment Angle | Horizontal +/-90º |
| Weight | 7.7-lb (3.5kg) [with brackets] |
| Enclosure | Weatherproof IP65 |
| Length | 43″ (109cm) |
Troubleshooting
| Receiver LED never turns ON and the buzzer never sounds | Test the power and ground wire with a voltage meter to ensure power is connected and is of the correct voltage |
| Buzzer does not sound if the sensor is triggered | -If jumper J1 is plugged in, this indicates that the beams are not aligned -If jumper J1 is not plugged in, buzzer should never sound |
| Receiver LED is ON and the buzzer sounds all the time | Realign the transmitter and receiver |
| Does not trigger when beam is broken | -Remount the curtain sensor, or repaint the surface to cut down on reflection -Lower the response time (SW1) |
| Receiver continuously triggers the alarm | -Realign the transmitter and receiver -Check that the tamper switch and the cover for the tamper switch are mounted correctly |
| False alarm | -Reinstall so that one sensor does not interfere with another sensor -Cut back on leafy vegetation -Do not mount under the edge of the roof -Mount under a roof or shelter |
Why buy Certified?
 |
 |
 |
|
Top USA Reseller Trusted since 1976 |
Your Team of Experts Pro Help when you need it |
Easy 30 Day Returns Satisfied or refunded |
Secure Checkout With
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.